Introducing a new age Variable Speed, Wet or Dry, Grinder/Polishing Machine

You can now mix and match belts, wheels and discs from a leading manufacturer of High Quality Innovative products for Grinding, Pre-Polishing and Finishing.  Add the ability to run these products at the optimum speed allowing these products to perform at there highest level while provide maximum life and performance. 

MAX 30 & MAX 24 (30 & 24 represent the size of the machine), can be run Wet or Dry.  Positioning the belts and wheels in the order that best fits your grinding and polishing requirements, allow you to proceed from start to finish effectively and efficiently, reducing time and effort.

 MAX 30 & 24 Variable Speed Grinder and Polisher, allows you to optimize and streamline your grinding and polishing by providing a wide variety of High Quality Innovative products such as 3M™ Diamond & Ceramic Belts, New Molded Wheels containing high performance abrasive minerals, and the new FX™ Molded Wheel technology which can eliminate your use of Tripoli compounds.  Discs from the latest Diamond Film technology, as well as Trizact™ Cerium Oxide disc for lapping crisp sharp edges and flats.

MAX 30 & 24 MACHINE SPECIFICATIONS

MAX 30 was built for the customer requiring wider spacing between wheels for larger parts, as well as manufacturing environments which may require special wheel configurations and other variables.

Applications and Product Recommendations

◆Jewelry Applications:

Grinding Step: Sand belting options with Expander Wheel.  Sprue and parting line removal For Gold, Silver, Platinum, Palladium, Titanium, Brass, Copper, and Tungsten Carbide.

1^st Step: M0101 MAX expander rubber wheel to be work different grit of sand belt.
             M0201 MAX 120 Grit sand Belt
             M0203 MAX 320 Grit sand Belt
             M0204 MAX 500 Grit sand Belt

Belting products provide fast cut rates with consistent finishes.  Always select the finest grade possible based on the removal you require, remembering that finer grades may take a few seconds longer on the initial removal, but will save you minutes on your pre-polish operations. TIP – run with a moderate water flow, water drops will be good to work.

2^nd Step: MAX XA Metal grinding wheel 240 grit = M0301 and different grit of MF multi-finishing and LD light
              deburring wheels.

MAX XA Metal grinding wheels also provide another media for removing sprues, parting lines and casting clean up for those desiring a hard wheel surface, but it also provides an excellent wheel for lapping edges and small critical flat areas. .  XA wheels and MAX LD & MF wheels No.M0650 MAX LD light deburring wheel, M0610 MAX MF multi finishing wheel 320 Grit, M0615 MAX MF wheel 600 Grit, M0620 MAX MF wheel 1000 Grit  provide a very fine pre-polish finish pattern with much longer life then tradition Silicon Carbide papers.  XA, LD and MF  wheels can also replace traditional hand filing steps, while retaining all you precious metal.  TIP: Run with moderate water flow and speed between 1200 & 1800 rpm

3^th Step: MAX MX Flexi Polishing Wheels 240 grade – Pre-polish replacing coarse grade Tripoli compound on Buff.

MAX MX Flexi Polishing Wheels uses a conformable system, which results in a wheel that can follow contours, curves and unique part geometries, while providing uniform finishes.  Unlike Tripoli Compound you can run the MAX MX Flexi wheel with water, reducing heat, eliminating sonic clean-up, and complete retention of precious metal. Choose a 240 grade depending on the work piece and the products used during steps 1-2 or 3. Consult with W & W CO., INC.  if you have any questions.  TIP: Run with light water and at 1200 to 1500 rpm.

4^th Step: MAX MX Flexi Polishing Wheels 600 grade – Pre- polish replacing medium grade Tripoli compound on
              Buff.

MX 600 grade 5^th & 6^th  provide you with another option based on your work piece.  Remember this option is right in line with your finishing system and does not require moving to another station, just a few seconds on either of these grades will reduce you final polish step.  TIP: Run with light water and run between 1200 to 1500 rpm.

5^th Step: MAX XA Flexi Polishing wheels 1500 – Fine-polish replacing white diamond or other fine grade Tripoli
              compounds.

XA 1500 grades provide the fine-polish finish.  Depending on the precious metal or semi-precious metal being polished you will find that this final XA wheel step will reduce your final Rouge Buff step significantly.  MAX XA Flexi Wheels will provide the time and cost savings you are look for. TIP: Run with light water and between 1800 to 2400rpm.

6^th Step: MAX XA M0512 Flexi polishing wheels 3000 for light touch for final polishing run between 2400 to
             3000rpm.

◆ Lapping Disc:

MAX30”  can run a 5” disc on the right side, with or without water.  You will find this convenient feature will allow you to flat lap edges on virtually any piece of jewelry or art object.    No.8317 3M lapping film 1200~2000 Grit, No.8318 3M lapping film 3000~4000 Grit, No.8319 3M lapping film 8000 Grit to meet your specific work piece requirements.

JEWELRY-LAPIDARY-ENAMEL-GLASS-CUSTOM KNIVES-CUSTOM METAL FAB GOLF CLUB REPAIR-STAINED GLASS-CRYSTAL-WATCH REPAIR

No. 1306 / 1307 User's Guide                    No. 1316 / 1317 User's Guide

Home

About Us

Products

Contact Us